P0020 – Intake Camshaft Position Actuator Circuit / Open (Bank 2) (OBD2)
P0020 means "Intake Camshaft Position Actuator Circuit / Open (Bank 2)". The control unit sees an open circuit: the electrical connection to the variable valve timing (VVT) system is interrupted, so no current can flow when the component is commanded or read.
Last updated
P0020 quick summary
| Fault code | P0020 |
|---|---|
| Meaning | Intake Camshaft Position Actuator Circuit / Open (Bank 2) |
| System | Powertrain (Engine & Transmission) |
| Vehicles | Generic OBD2 |
| Severity | Medium |
| Can I drive? | Usually yes, gently. The adjuster returns to its base position, so power and fuel economy drop. Check the oil level immediately – low oil is a common cause and dangerous for the engine. |
| Repair cost | €20 – €1,500 |
How variable valve timing works
Variable valve timing adjusts when the valves open and close depending on engine speed and load; these codes cover the camshaft adjusters, their control solenoids and the timing they achieve.
Most modern engines turn the camshaft relative to its sprocket using an oil-pressure-driven adjuster (cam phaser). A control solenoid (oil control valve) on the cylinder head directs oil to one side or the other of the adjuster on command of the engine control unit. The camshaft sensor reports the actual position, and the control unit compares it with the target.
Codes in this group cover the solenoid's electrical circuit (open, low, high), the solenoid's performance, and the camshaft timing being 'over-advanced' or 'over-retarded' – that is, the actual position is further from the target than allowed. Some engines also have valve lift control solenoids, which use the same type of codes.
Because the system is hydraulic, the oil is as important as the parts: low oil level, the wrong viscosity, sludge or a clogged solenoid screen are very frequent causes. Timing chain stretch can also push the camshaft out of its expected window.
Bank 2 is the cylinder row that does NOT contain cylinder 1, so this code only appears on V6, V8, V10, V12 and boxer engines.
On VAG vehicles (VW, Audi, Škoda, Seat, Cupra), VCDS and older VAG testers can show this code as the five-digit VAG code 16404 (P0020). Both numbers mean the same fault.
Symptoms of P0020
- Check Engine light on
- Rough or unstable idle
- Loss of power, especially at low or high rpm
- Rattle at cold start (adjuster or chain)
- Higher fuel consumption
Most common causes of P0020 (most likely first)
Mechanic's Pro Tip
An oil change with the correct specification oil fixes a surprising number of VVT codes, especially if the car is overdue for service. Do the cheap check first: oil level, oil quality and the solenoid screen.
1.Unplugged, loose or corroded connector
Most likelyOften after previous repair work in the area.
2.Broken wire in the harness
Typical at bends, near the engine mounts and where the harness rubs on brackets.
3.Burnt-out winding or internal break in the variable valve timing (VVT) system
4.Low oil level, wrong oil or sludge
The adjusters need the correct oil pressure and viscosity.
5.Sticking or clogged VVT solenoid (oil control valve)
Dirt or sludge on the solenoid screen stops it from moving freely.
6.Faulty camshaft adjuster (phaser)
Worn locking pin or internal seals – often heard as a rattle at start.
7.Stretched timing chain
Shifts the camshaft out of its expected range.
Step-by-step diagnostic guide
- 1
Check oil and read codes
Check the oil level and condition first. Read all codes and note which bank and camshaft (intake or exhaust) are affected.
- 2
Measure resistance and continuity
Unplug the variable valve timing (VVT) system and measure its resistance across the terminals. An infinite (OL) reading confirms an internal break. If the component is fine, check each wire back to the control unit for continuity.
Multimeter: Solenoids and heaters typically read a few ohms to a few dozen ohms; "OL" means open. Wire continuity: below about 1 Ω.
- 3
Inspect the solenoid
Remove the VVT solenoid, check its screen for debris and the O-rings for damage. Clean the screen carefully.
- 4
Test the solenoid
Measure the coil resistance and command the solenoid with the scan tool – it should click and the camshaft angle in live data should change.
Multimeter: Typical VVT solenoid resistance: about 6–15 Ω (check the specification).
- 5
Swap solenoids
On engines with identical intake and exhaust solenoids, swap them and see if the code moves.
- 6
Check timing and adjusters
If the solenoid is fine, check the timing chain stretch and the camshaft adjusters. After repairs, clear codes and run any camshaft adaptations.
Frequently asked questions
Can I keep driving with P0020?
Usually yes, gently. The adjuster returns to its base position, so power and fuel economy drop. Check the oil level immediately – low oil is a common cause and dangerous for the engine.
How much does it cost to fix P0020?
Typical repair costs are 20 € – 1500 €, depending on the cause and the vehicle. The most common fixes are: unplugged, loose or corroded connector; broken wire in the harness; burnt-out winding or internal break in the variable valve timing (VVT) system. Always confirm the cause with the tests above before buying parts.
What do over-advanced and over-retarded mean?
The camshaft is either further ahead (advanced) or further behind (retarded) than the control unit commanded. It usually means the adjuster or solenoid is not responding correctly, or the timing chain is stretched.
Can low oil cause VVT codes?
Yes. The camshaft adjusters work with oil pressure, so low oil level, the wrong viscosity or sludge are among the most common causes.
What is the difference between P0020 and similar codes?
P0020 belongs to a group of codes for the same component that differ in the type or location of the fault: P0013 – Exhaust Camshaft Position Actuator Circuit / Open (Bank 1); P0014 – Exhaust Camshaft Position Timing - Over-Advanced (Bank 1); P0015 – Exhaust Camshaft Position Timing - Over-Retarded (Bank 1); P0021 – Intake Camshaft Position Timing - Over-Advanced (Bank 2); P0022 – Intake Camshaft Position Timing - Over-Retarded (Bank 2); P0023 – Exhaust Camshaft Position Actuator Circuit / Open (Bank 2). The tests on this page apply to the whole group; the type of fault tells you where to start.
Related fault codes
- P0021Intake Camshaft Position Timing - Over-Advanced (Bank 2)
- P0022Intake Camshaft Position Timing - Over-Retarded (Bank 2)
- P0023Exhaust Camshaft Position Actuator Circuit / Open (Bank 2)
- P0024Exhaust Camshaft Position Timing - Over-Advanced (Bank 2)
- P0025Exhaust Camshaft Position Timing - Over-Retarded (Bank 2)
- P0026Intake Valve Control Solenoid Circuit Range/Performance (Bank 1)
- P0027Exhaust Valve Control Solenoid Circuit Range/Performance (Bank 1)
- P0028Intake Valve Control Solenoid Circuit Range/Performance (Bank 2)
This guide is for information only. Working on vehicles can be dangerous — if you are unsure, have the car checked by a qualified mechanic. Values can differ between model years; always check the manufacturer's repair information.