Skip to content

P0064 – HO2S Heater Control Circuit High (Bank 2, Sensor 3) (OBD2)

P0064 means "HO2S Heater Control Circuit High (Bank 2, Sensor 3)". The voltage in the oxygen sensor heater circuit is above the permitted maximum. For most sensors this points to an open signal or ground wire – the signal "floats" up to the reference voltage – or to a short to voltage.

Last updated

P0064 quick summary

Fault codeP0064
MeaningHO2S Heater Control Circuit High (Bank 2, Sensor 3)
SystemPowertrain (Engine & Transmission)
VehiclesGeneric OBD2
SeverityLow
Can I drive?Yes. The engine runs normally once the exhaust has warmed the sensor, but emissions and fuel consumption are higher after cold starts and the car may fail an emissions test.
Repair cost€5 – €300

Why oxygen sensors have heaters

The oxygen sensor heater brings the sensor up to its working temperature quickly after a cold start, so fuel control and catalytic converter monitoring can start early.

An oxygen sensor only works properly at several hundred degrees Celsius. Exhaust gas alone takes too long to heat it, so every modern sensor has an electric heating element. The heater usually gets battery voltage through a fuse or relay, and the engine control unit switches the ground side on and off to control the temperature.

The control unit monitors the heater current and resistance. If the circuit is open, shorted or the resistance is outside the expected window, it stores a heater code for that specific sensor (bank and sensor number). Until the sensor is hot enough, fuel control stays in open loop, which increases emissions and fuel consumption.

Heater faults are among the most common oxygen sensor problems. Because the heater is built into the sensor, a failed heater element normally means replacing the whole sensor – but blown fuses and wiring damage near the exhaust are common too and much cheaper to fix.

Bank 2 is the cylinder row that does NOT contain cylinder 1, so this code only appears on V6, V8, V10, V12 and boxer engines.

Sensor 3 is a third oxygen sensor further down the exhaust, used on some engines with an additional catalytic converter.

Symptoms of P0064

  • Check Engine light on
  • Slightly higher fuel consumption, especially on short trips
  • Rough running in the first minutes after a cold start
  • Failed emissions test
  • Often no noticeable driving symptoms

Most common causes of P0064 (most likely first)

Mechanic's Pro Tip

Measure the heater resistance before buying a sensor. If it reads correctly, the problem is in the fuse, supply or wiring – often a melted cable touching the exhaust. That simple measurement saves the price of an unnecessary sensor.

  1. 1.Open circuit in the signal or ground wire

    Most likely

    A loose ground connection is a very common cause.

  2. 2.Signal wire shorted to the 5 V reference or battery voltage

  3. 3.Faulty oxygen sensor heater

  4. 4.Burnt-out heater element in the oxygen sensor

    The most common cause – the sensor must be replaced.

  5. 5.Wiring damaged by heat or chafing

    The sensor cable often runs close to the exhaust.

  6. 6.Corroded or loose connector

    Underbody connectors are exposed to water and road salt.

  7. 7.Fault in the control unit's heater driver

    Rare; usually after a shorted heater or wiring damaged the driver.

Step-by-step diagnostic guide

  1. 1

    Read codes

    Read all codes and note which bank and sensor are affected. Several heater codes at once usually point to a shared fuse or supply.

  2. 2

    Check signal and ground

    With the ignition on and the oxygen sensor heater plugged in, back-probe the signal and ground wires. A signal stuck at reference or battery voltage points to an open ground/signal wire or a short to voltage.

    Multimeter: Ground wire to battery negative: below about 0.1 V. Signal stuck at about 5 V (or 12 V) = open or short to voltage.

  3. 3

    Check the fuse and supply voltage

    With the ignition on, check for battery voltage on the heater supply wire at the sensor connector.

  4. 4

    Measure the heater resistance

    Unplug the sensor and measure across the two heater terminals (usually the two wires of the same colour).

    Multimeter: Typical heater resistance: about 2–15 Ω at room temperature depending on the sensor. 'OL' means the heater is burnt out.

  5. 5

    Check the ground (control) wire

    Check the control wire from the sensor to the engine control unit for continuity and shorts to ground or voltage.

  6. 6

    Replace and clear

    Replace the sensor if the heater is open or shorted, repair wiring if damaged, then clear codes and confirm the heater test passes after a cold start.

Frequently asked questions

Can I keep driving with P0064?

Yes. The engine runs normally once the exhaust has warmed the sensor, but emissions and fuel consumption are higher after cold starts and the car may fail an emissions test.

How much does it cost to fix P0064?

Typical repair costs are 5 € – 300 €, depending on the cause and the vehicle. The most common fixes are: open circuit in the signal or ground wire; signal wire shorted to the 5 V reference or battery voltage; faulty oxygen sensor heater. Always confirm the cause with the tests above before buying parts.

Is an oxygen sensor heater code serious?

Not urgent for the engine, but fuel control starts later after each cold start, so emissions and consumption rise. It should be fixed before the next emissions test.

Can I replace only the heater?

No. The heater element is built into the sensor, so a failed heater means replacing the oxygen sensor.

What is the difference between P0064 and similar codes?

P0064 belongs to a group of codes for the same component that differ in the type or location of the fault: P0061 – HO2S Heater Resistance (Bank 2, Sensor 3); P0062 – HO2S Heater Control Circuit (Bank 2, Sensor 3); P0063 – HO2S Heater Control Circuit Low (Bank 2, Sensor 3); P0135 – O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 1); P0141 – O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 2); P0147 – O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 3). The tests on this page apply to the whole group; the type of fault tells you where to start.

Related fault codes

This guide is for information only. Working on vehicles can be dangerous — if you are unsure, have the car checked by a qualified mechanic. Values can differ between model years; always check the manufacturer's repair information.