Skip to content

P0092 – Fuel Pressure Regulator Control Circuit High (OBD2)

P0092 means "Fuel Pressure Regulator Control Circuit High". The voltage in the fuel pressure control system circuit is above the permitted maximum. For most sensors this points to an open signal or ground wire – the signal "floats" up to the reference voltage – or to a short to voltage.

Last updated

P0092 quick summary

Fault codeP0092
MeaningFuel Pressure Regulator Control Circuit High
SystemPowertrain (Engine & Transmission)
VehiclesGeneric OBD2
SeverityHigh
Can I drive?Not recommended. Low pressure can make the engine cut out in traffic; a detected fuel leak (P0093) is a fire risk – stop and check for leaks immediately.
Repair cost€20 – €2,500

How fuel pressure is controlled

The engine needs fuel at a precise pressure; these codes mean the measured fuel pressure is too low, too high, or the pressure regulator or its circuit does not work as commanded.

Petrol engines with port injection usually run at about 3–4 bar, supplied by an electric pump in the tank. Direct-injection petrol engines add a high-pressure pump driven by the camshaft that raises the pressure to roughly 100–350 bar. Common-rail diesels use a high-pressure pump that produces from a few hundred up to more than 2,000 bar.

The control unit sets the target pressure and controls it with a pressure regulator valve, a volume (metering) control valve, or both, using the rail pressure sensor as feedback. Codes in this group report pressure that is too low (P0087), too high (P0088), a regulator that does not achieve the target (P0089), a fault in the regulator's electrical circuit (P0090–P0092) or a detected fuel leak (P0093, P0094).

Low pressure causes hesitation, cutting out and limp mode; high pressure is less common and often caused by a stuck regulator. A large-leak code on a diesel is a safety issue: high-pressure fuel leaking onto a hot engine is a fire risk.

On VAG vehicles (VW, Audi, Škoda, Seat, Cupra), VCDS and older VAG testers can show this code as the five-digit VAG code 16476 (P0092). Both numbers mean the same fault.

Symptoms of P0092

  • Loss of power, hesitation or limp mode
  • Long cranking or no start
  • Engine cuts out, especially under load
  • Smell of fuel or visible fuel leak (leak codes)
  • Check Engine light on

Most common causes of P0092 (most likely first)

Mechanic's Pro Tip

Always cut open the old fuel filter on a car with low rail pressure. Shiny metal particles mean the high-pressure pump is disintegrating – replacing just the pump without flushing the whole system will destroy the new one too.

  1. 1.Open circuit in the signal or ground wire

    Most likely

    A loose ground connection is a very common cause.

  2. 2.Signal wire shorted to the 5 V reference or battery voltage

  3. 3.Faulty fuel pressure control system

  4. 4.Clogged fuel filter or air in the low-pressure system

    The cheapest and one of the most common causes of low pressure.

  5. 5.Weak in-tank fuel pump

    Not enough supply to the high-pressure pump or rail.

  6. 6.Leaking injector or fuel line

    Internally leaking injectors return too much fuel; external leaks are dangerous.

Step-by-step diagnostic guide

  1. 1

    Read codes and pressure data

    Read all codes and compare specified and actual fuel pressure in live data at idle and during a full-load acceleration.

  2. 2

    Check signal and ground

    With the ignition on and the fuel pressure control system plugged in, back-probe the signal and ground wires. A signal stuck at reference or battery voltage points to an open ground/signal wire or a short to voltage.

    Multimeter: Ground wire to battery negative: below about 0.1 V. Signal stuck at about 5 V (or 12 V) = open or short to voltage.

  3. 3

    Check for leaks

    With the engine running, look for fuel leaks at the pump, lines, rail and injectors. Stop immediately if fuel is leaking onto hot parts.

  4. 4

    Check the low-pressure side

    Check the fuel filter, the in-tank pump and the supply lines. Measure the low-pressure supply with a gauge where possible.

    Multimeter: Many in-tank pumps deliver about 3–6 bar; check the specification for your engine.

  5. 5

    Test the regulator and sensor

    Check the regulator/metering valve resistance and response in output tests; compare the rail pressure sensor with key-on, engine-off values.

  6. 6

    Test injectors and pump

    On diesels, do an injector leak-off test. Replace the high-pressure pump only when the rest of the system is confirmed good, and check the old filter for metal debris.

Frequently asked questions

Can I keep driving with P0092?

Not recommended. Low pressure can make the engine cut out in traffic; a detected fuel leak (P0093) is a fire risk – stop and check for leaks immediately.

How much does it cost to fix P0092?

Typical repair costs are 20 € – 2500 €, depending on the cause and the vehicle. The most common fixes are: open circuit in the signal or ground wire; signal wire shorted to the 5 V reference or battery voltage; faulty fuel pressure control system. Always confirm the cause with the tests above before buying parts.

What is the difference between P0087 and P0088?

P0087 means the fuel pressure is too low, P0088 that it is too high. Low pressure is usually a supply problem; high pressure is more often a sticking regulator or a sensor fault.

Can a fuel filter cause low fuel pressure codes?

Yes. A clogged or wrong filter is one of the most common causes, especially on diesels in cold weather when the fuel thickens.

What is the difference between P0092 and similar codes?

P0092 belongs to a group of codes for the same component that differ in the type or location of the fault: P0089 – Fuel Pressure Regulator Performance; P0090 – Fuel Pressure Regulator Control Circuit; P0091 – Fuel Pressure Regulator Control Circuit Low; P0093 – Fuel System Leak Detected - Large Leak; P0094 – Fuel System Leak Detected - Small Leak; P2293 – Fuel Pressure Regulator 2 Performance. The tests on this page apply to the whole group; the type of fault tells you where to start.

Related fault codes

This guide is for information only. Working on vehicles can be dangerous — if you are unsure, have the car checked by a qualified mechanic. Values can differ between model years; always check the manufacturer's repair information.